AMO® III spacing assembly screw 7.5 A2 type 2 cylinder head 8.0 mm 0239230112

Գլխավոր

Ամրացման տեխնոլոգիաներ

Շրջանակ ամրագրելու համակարգեր

Metal frame dowels

Spacing assembly screw, frame

AMO® III spacing assembly screw 7.5 A2 type 2 cylinder head 8.0 mm

0239230112

Նմանատիպ ապրանքներ

Spacing assembly screw AMO® III 11.5

Spacing assembly screw AMO®-Y 11.5 mm

Amo® III spacing assembly screw 7.5 TYPE 2 cylinder head 7.5 mm

Amo® III spacing assembly screw 7.5 type 3 half round head

AMO® III spacing assembly screw 7.5 type 2 cylinder head 8.0 mm

AMO® III spacing assembly screw 7.5 TYPE 1 countersunk milling head

Spacing assembly screw AMO® III 11.5

Spacing assembly screw AMO®-Combi 7.5/11.5

Amo® III spacing assembly screw 7.5 type cylinder head 7.5 mm

Spacing assembly screw AMO®-Y 7.5mm

Նմանատիպ ապրանքներ

AMO® III spacing assembly screw 7.5 A2 type 2 cylinder head 8.0 mm

Արտիկուլ: 0239230112

Գինը գրանցումից հետո

Հարցերի դեպքում կարող եք զանգահարել՝ +374(0)10 349347, 349348

0x - +	Գինը գրանցվելուց հետո	Ավելացնել զամբյուղ

- +

Գինը գրանցվելուց հետո

Ավելացնել զամբյուղ

Կարդալ Ապրանքի նկարագրությունը

Տեղեկություններ ապրանքի վերաբերյալ

Կատալոգի էջը PDF ֆորմատով 1

Տեխնիկական բնութագիր Կիրառումը Տեխնիկական ինֆորմացիա

Specification

For mounting windows in concrete and solid stone masonry. With small cylinder head. Stainless steel A2. With AW30 drive. Ideal for frames made of thermally-treated wood.

Positive-locking, removable anchorage with no expansion pressure
Saves time u2014 no anchors required
Short installation times, as no tools are required for insertion
AW drive for longer bit service life, improved power transmission and no ejection forces
Push-through installation
Immediate load-bearing capacity u2014 no waiting after insertion
Positive locking for high load-bearing capacity
Removable
Virtually no expansion forces on insertion

Notice

It is important to check that the components are correctly installed for the specific construction conditions (e.g. weight of window casement, surface properties, hole pattern in the brick).

Application

Information for use

Guidelines for planning and executing the installation of windows and house doors, 2010 edition

Art. no. 5995 000 000:

The fixture must safely transfer all standard forces affecting the window to the structure and the foundation. The total load must therefore be calculated from e.g. the window load, wind load and working load (see DIN 1055). The currently applicable building regulations stipulate that buildings and their components must be planned in such a way that they do not endanger human life and health or pose a risk to public safety. Attachment of the windows must also comply with this criterion.

Window walls according to former DIN 18056 standard or elements with a surface greater than 9 mu00b2 and accident-proof glazing as specified in the German technical rules for safety glazing (TRAV) or DIN 18008-4

The DIN 18056 standard applied to window walls with a minimum surface area of 9 mu00b2 and a minimum side length of 2 m on the shortest side. Anchors with a general construction permit or European Technical Approval or with individual approval should be used for this application. Similarly, only anchors with a general construction permit or European Technical Approval or with individual approval must be used to attach accident-proof glazing as specified in the German technical rules for safety glazing (TRAV) or DIN 18008-4.

Other information

It is important to check that the components are correctly installed for the specific construction conditions (e.g. weight of window casement, surface properties, hole pattern in the brick). Accident-proof glazing as specified in the German technical rules for safety glazing (TRAV) or DIN 18008-4 may only be attached with the AMO Combi screw if the appropriate individual approval has been obtained before installation starts.

Drill perforated and hollow blocks with a rotary drill (without impact mechanism)

Drill perforated and hollow blocks with a rotary drill (without impact mechanism)
Align window frames using alignment clamps or AMO^u00ae Bag
Screw length = frame width + gap + screw-in depth (see also 55.2 Amo^u00ae III 11.5 mm)